ADVANCED BATTERY CHARGER

TDCX12xx SERIES

90 – 264 VAC

  • UNIVERSAL AC INPUT WITH ACTIVE PFC
  • COMPATIBLE WITH LEAD ACID, LI-ION, GEL AND AGM BATTERIES
  • SUPPORT OPTIONAL REMOTE CONTROLLER (CR-1)
  • VOLTAGE/TEMP. COMPENSATION WITH BATTERY TEMP. SENSOR (OPTIONAL)
  • 2-STAGE FAN SPEED CONTROL
  • DRY CONTACT FOR ALARM
  • HIGH EFFICIENCY AND HIGH RELIABILITY
  • BUILT-IN BATTERY RESCUE FUNCTION
  • BUILT-IN ENGINE START BATTERY (ESB) OUTPUT FUNCTION
  • PROTECTION:
    SHORT CIRCUIT/ OVER VOLTAGE/ OVER TEMPERATURE / BROWN-OUT
  • WITHSTAND 2G VIBRATION TEST
  • RS-232 COMMUNICATION INTERFACE
  • OUTPUT POWER OK SIGNAL
PDF DATASHEET
SEE VIDEO
MODEL TDCX1215 TDCX1225 TDCX1235 TDCX1250 TDCX1280
OUTPUT BATTERY TYPE LEAD ACID / Li-ion / GEL / AGM
STANDARD BOOST CHARGE VOLTAGE 14.4 V / 14.7 V (SELECT BY S1-1)
STANDARD FLOAT CHARGE VOLTAGE 13.8V / 13.5V (SELECT BY S1-2)
MAIN RATED CURRENT 15 A 25 A 35 A 50 A 80 A
CURRENT RANGE 0 ~ 15 A 0 ~ 25 A 0 ~ 35 A 0 ~ 50 A 0 ~ 80 A
MAIN OUTPUT 1 2 2 3 3 1 2 2 3 3
ESB OUT 1 1 1
ESB OUTPUT VOLTAGE / CURRENT 13.8 V / 2 A
BATTERY CHARGING MODE 3 – STAGE CHARGING CAPABILITY (I UOU)
SINGLE OUTPUT CURRENT LIMIT 15 A 25 A 35 A 40 A 40 A
INPUT VOLTAGE RANGE 90 -264VAC
POWER FACTOR (TYP.) PF > 0.92 @ FULL LOAD
FREQUENCY RANGE 47 – 63 Hz
EFFICIENCY AT 230 VAC (TYP.) 87%
AC CURRENT (TYP.) 2.5 A / 100 VAC 4.1 A / 100 VAC 6.2 A / 100 VAC 8.24 A / 100 VAC 13.3 A / 100 VAC
1.07 A / 240 VAC 1.8 A / 240 VAC 2.8 A / 240 VAC 3.6 A / 240 VAC 5.4 / 240 VAC
LEAKAGE CURRENT FOR EARTH <1 mA / 240VAC
PROTECTION SHORT CIRCUIT CURRENT IS REDUCED TO <1A CONTINUED 30 SECONDS , FAN WILL OPERATE 30 SECONDS THEN TURN OFF
OVER VOLTAGE 17.5V ± 1% – PROTECTION TYPE: SHUT DOWN OUTPUT (RECOVERY AFTER RESETTING AC POWER ON)
OVER TEMPERATURE CHARGER OVER TEMPERATURE 100 ±5°C DETECTED BY HEAT SINK
PROTECTION TYPE: AUTO RECOVERY AFTER HEAT SINK TEMPERATURE GOES DOWN TO 50°C
BATTERY OVER TEMPERATURE 52 ±5°C (OPTIONAL DEVICE – TEMPERATURE SENSOR), CONNECT ON CN3
FUNCTION ALARM SIGNAL NC. / NO. RELAY CONTACT OUTPUT
COMMUNICATION RS485 / RS323 COMMUNICATION PROTOCOL
TEMPERATURE COMPENSATION -10 mV / 0.5°C PROVIDED BY OPTIONAL DEVICE – TEMPERATURE SENSOR
CHARGING SLEEP MODE (SEE NOTE 4) BY REMOTE CONTROL AND DIP SWITCH (LOW NOISE MODE)
REMOTE CONTROL 3 COLOUR LED AND BOTTOM FOR ON / OFF AND SLEEP MODE CONTROL.
ENVIRONMENT WORKING TEMPERATURE -20°C ~ 50°C FULL LOAD, DERATE TO 75% AT 60°C
WORKING HUMIDITY 20 ~ 90 % RH NON-CONDENSING
STORAGE TEMP. / HUMIDITY 40°C ~ +85°C, 20 ~ 90 % RH
TEMP. COEFFICIENT ± 0.03% (0°C ~ 50°C)
VIBRATION 10 ~ 500 Hz, 2G 10 MIN. / 1 CYCLE PERIOD FOR 60 MIN EACH ALONG X, Y, Z AXES
SAFETY & EMC
(SEE NOTE 2)
SAFETY STANDARDS CERTIFIED EN 60335-1, EN 60335-2-29
WITHSTAND VOLTAGE I/P – O/P: 4242 VDC, I/P-FG: 1768 VDC, O/P-FG: 700 VDC
ISOLATION RESISTANCE I/P-O/P: 100M OHMS / 500 VDC
EMI CONDUCTION AND RADIATION EN 55022
HARMONIC CURRENT EN 61000-3-2; EN 61000-3-3
EMS IMMUNITY EN 61000-4-2, 3, 4, 5, 6, 8, 11; ENV 50204
OTHERS DIMENSION (W x H x D) 7.21” x 2.83” x 9.58” 7.21” x 2.83” x 9.58” 7.21” x 2.83” x 9.58” 9.58” x 3.01” x 10.72” 9.58” x 3.01” x 10.72”
183 X 72 X 243.4 mm 183 X 72 X 243.4 mm 183 X 72 X 243.4 mm 213 X 76.5 X 272.4 mm 213 X 76.5 X 272.4 mm
PACKING 3.5 lbs [1.6 kg] 3.7 lbs [1.7 kg] 4.2 lbs [1.9 kg] 6.83 lbs [3.1 kg] 8.8 lbs [4.0 kg]
NOTES 1. All parameters not specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.
2. T he charger is considered a component which will be installed into a final equipment. T he final equipment must be re-confirmed that it still meets EMC directives.
3. Before charging, make sure the battery charger and battery specifications are compatible.
4. When using sleep mode, please refer to charging current vs. Ambient temperature de-rating curve.

Technology Dynamics, Inc. Rugged DC UPS Systems